Movable Liftable Vacuum Feeding Conveyor 220V 025356

Movable Liftable Vacuum Feeding Conveyor 220V

Product Overview

The vacuum feeding conveyor is a modern professional powder and particle conveying device integrating vacuum conveying, lifting positioning and movement convenience. It is suitable for the industries of food, breeding, chemical and so on and can be used for overhead conveying and feeding various particles and powder.

It uses a vacuum pump or Roots blower to suction the air, so that the inlet of the suction nozzle and the whole system are in a certain vacuum state. The powder particles are sucked into the nozzle along with the outside air to form the material and air stream which passes through the suction pipe and reaches the hopper in the hopper, air and material separation are conducted in the hopper, and the separated materials enter the receiving equipment. The vacuum feeder is equipped with a compressed air back flushing device. Each time the material is discharged, the compressed air pulse conducts back flushing on the filter, and the powder absorbed on the surface of the filter drops to ensure the normal operation of the material suction.

Product Parameters

Model	ZKS-3
Voltage	220V single-phase
Motor power	3Kw
Maximum conveying quantity	900kg/h
Air pressure	0.4-0.6MPa

Note：The conveying capacity is the limit capacity, and is measured when the conveying distance is 5 meters and the conveying material is flour. The longer the conveying distance, the lower the conveying capacity. In addition, the conveying capacity is closely related to the material properties.

Attention

1. The feeding conveyor is not suitable for conveying too wet, sticky and heavy materials.

2. Before use, please connect the air compressor to ensure the air is clean and dry.

3. There is no plug on the control box. Please let a professional electrician connect the power supply with reliable grounding.

Product Features

Control Box

The vacuum conveyor control system is easy to operate and adjustable in parameter, the feeding time and discharging time can be freely adjusted and set as needed, the working state is also clearly shown, and the operation practicability is higher.

Vacuum Gauge

The vacuum gauge can clearly display the air pressure, facilitating real-time monitoring of air pressure and working state, achieving fault diagnosis and positioning and ensuring the production safety and efficiency.

Hand Crank

The hand crank is designed for manually driving the vacuum hopper to move up and down so as to meet different discharging requirements, and is convenient to use, simple in structure and low in fault rate and cost.　

Vacuum Hopper

The vacuum hopper is made of stainless steel materials, well ensuring the high structural strength, corrosion resistance and long service life. The hopper is of a sealed structure, effectively avoiding material contamination.

Suction Nozzle

The stainless steel suction nozzle is matched with a 5m PVC steel wire hose to achieve smooth suction of various particles and powder, ensuring uniform feeding without jamming, well adapting to various working environments.

Filter

The filter is designed for achieving efficient filtering, effectively avoiding powder diffusion, reducing the material waste whiling improving the working environment. The filter is resistant to corrosion and long in service life.

Clamp

The clamp is used to firmly fasten the hopper body, preventing the hopper body from deformation and keeping the hopper body stable. The clamp is simple in structure, easy to assemble and disassemble and low in cost.　

Compressed Air Back Flushing

The compressed air pulse can conduct back flushing on the filter in the discharging process, effectively removing the powder attached to the surface of the filter, and ensuring normal suction operation of the machine.

Universal Wheel

The universal wheels are installed at the bottom of the device, facilitating flexible movement of the device to adapt to different working environment, greatly saving time and labor and improving the working efficiency and practicability.　

Operation Method

Before using the device, please make sure that the compressed air source is clean and dry, and the working pressure is 0.4-0.6mpa.

1. The hopper of the feeding machine is generally fixed on the receiving equipment, or fixed on the hand-cranked trolley. When fixed on the hand-cranked trolley, the hopper can move up and down. According to the height of the receiving equipment, adjust the hopper of the feeding machine. When the hopper of the receiving equipment (such as the packaging machine) is high, the hopper of the vacuum feeder needs to be fixed on a special support.

2. Connect the suction nozzle to the hopper through a hose, connect the hopper and Roots blower with a hose, and tighten the hopper with the hose clamp.

3. Connect the power supply. The power supply should adopt three-phase five-wire cable, because the control circuit needs ‘work 0’, and ‘protection 0’ is still needed for safety. Another function of the ‘protection 0’ is to eliminate the interference of the static electricity generated during material conveying to the control chip to avoid causing the control system to crash. Therefore, the 'protection 0' must be connected.

4. Insert the Φ10 compressed air tube into the air inlet of the system (filtering and pressure reduction), adjust the pressure reducing valve to ensure that the pressure of the system is maintained at 0.6Mpa, and connect the external compressed air pipe joint and the external compressor air connector on the vacuum hopper according to the pipe connection diagram.

5. Turn on the power, open the box door, and turn on the three-phase air switch. At this time, the feeding time and discharging time displayers on the control box are on.

6. Adjust the feeding time and discharging time. By pressing the increase and decrease buttons, set the feeding time to 8-20 seconds, and set the discharging time to 4-8 seconds.

7. Press the on/off button to turn on the vortex air pump. Check the rotating direction of the vacuum pump. If there is no air exhaust from the exhaust port, the motor conducts reversal rotation, turn off the on/off button, and change the wiring phase sequence of the power supply until the air pump rotates correctly.

8. Press the on/off button to start the vortex air pump, insert the suction nozzle into the material box, and start feeding. Suction-discharge (simultaneously compressed air conducts back flushing on the filter) is a working cycle. The vacuum feeder will automatically cycle until the hopper of the receiving equipment (such as the packaging machine) is filled with materials (the material level switch is on at this time).

9. When the material level in the hopper of the receiving equipment is lower than the material level switch, the pneumatic three-way valve automatically conducts reversing operation, and the system enters the suction-discharging cycle again until the hopper is filled with materials.

10. In the material conveying process, large static electricity will be generated due to friction. In order to eliminate the static electricity, reliable grounding of the equipment shell should be taken into account.

Product Display

Item Number (025356): 1 x Vacuum Feeding Conveyor 220V

You can make order with no worry.
Any concern just feel free to let us know, we'll reply in 24 hours in normal condition.
Handling Time: Shipping is usually made in 1-3 business days after payments cleared. Orders are processed from Monday-Friday; Not on the weekends & public holidays.
Warranty: 6 months' warranty for the machines, not for the consumables.
We stand behind our products all the item, so even if your warranty period has expired, you can still seek for service or technical support from us with low cost.